Hardware
Solid-brass feet, hooks, knobs, and stays - machined in the USA to match the hinges, not sourced to fill a bin.
+/- 0.005 inMachined tolerance
Solid brassBar stock, not stamped
Made in USACut and milled, not imported
4.9 average
726 verified reviews
-
Brass Stop Hinges
A solid-brass box hinge with a built-in stop. The lid opens to 95° and holds there — no separate lid stay, no chain, no sag. The stop is machined into the knuckle, so one pair does the work of a hinge and a lid support, with nothing extra to mount...Regular price From $60.00Regular priceUnit price per -
Offset Pivot Hinges
A knife hinge that carries the door on a single pivot pin — top and bottom — so the only thing visible from the front is a thin brass line at the edge. No barrel, no leaves stamped across the face. The door appears to swing on nothing. This is the...Regular price From $61.00Regular priceUnit price per -
Brass Butt Hinges
A full-mortise butt hinge milled from solid brass bar stock — not stamped or rolled. The knuckle is true, the leaves are flat and thick, and the pin runs straight, so the door swings without play and the gap stays even top to bottom. The differenc...Regular price From $58.00Regular priceUnit price per -
Small Box Knobs
A small solid-brass knob for boxes, small drawers, and lids — a flattened dome face ringed by a turned band, pressure-fit and glued so nothing shows but the brass. No screw head, no backplate, just a clean point to grip. On a small box, the knob i...Regular price From $13.00Regular priceUnit price per -
Push Button Latches
A solid-brass push-button latch that sits flush and hides inside the box. Press the button, the spring-loaded bar releases, the lid opens. Close it and it catches with a click you can feel. This is the closure for the maker who wants the box to lo...Regular price From $77.82Regular priceUnit price per -
Side Rail Hinges
A full-mortise side rail hinge with a built-in 95° stop, milled from thick solid brass. The lid swings up, catches at 95°, and holds — no separate lid stay, no chain. The stop is built into the hinge, so the inside of the box stays clean. Where a ...Regular price From $49.00Regular priceUnit price per -
Center Pivot Hinges
A center pivot hinge that mortises into the top and bottom of the door — only the pivot shows. The door swings free of the frame on a single axis, so you can run a door with no visible barrel and no side clearance to the case. Same idea as the off...Regular price From $51.12Regular priceUnit price per -
Precision Ball Catches
A spring-loaded brass ball catch that holds a door shut and lets it go with a press. That click when it seats, and a clean release when you pull. A steel ball rides in a machined brass cylinder against a matching keeper, so the catch is positive e...Regular price From $26.00Regular priceUnit price per -
LH-201 Lift Off Hinge
Solid-brass lift-off hinge: the two leaves separate, so the door lifts straight off its pins without unscrewing anything. Hang it, level it once, and from then on the door comes off and goes back on in seconds — for finishing, for fitting, for mov...Regular price $58.00Regular priceUnit price per -
Round Box Feet
A small solid-brass box foot — a turned sphere tapering to a disk — that lifts a box off the surface and finishes the bottom edge. Pressure-fit and glued on a 5/16"" dowel, so it sits flush and shows nothing but brass. Feet are the detail most mak...Regular price $19.00Regular priceUnit price per -
Latch Supported Lid Stay
A lid stay that mortises into the side of the box and anchors into the lid — it catches the lid at the open position and holds it, so the lid doesn't fall back or strain the hinges. The flanged anchor is precision machined and glued into the lid f...Regular price $48.00Regular priceUnit price per -
Quadrant Hinges
A quadrant hinge machined to the tolerance the install actually demands. The curved quadrant arm sweeps through a mortise in the box wall, so the lid opens, stops, and stays — the look of a high-end humidor or presentation box, with no visible lid...Regular price $124.00Regular priceUnit price per -
Shelf Support Pins
A shelf support pin with a milled brass head and a clean barrel peg — the part of an adjustable shelf that actually shows. It drops into the K-2 sleeve for a fit with no rattle and no slop, so the shelf sits dead level and stays there. Most shelf ...Regular price From $30.00Regular priceUnit price per -
Shelf Support Sleeves
The sleeve half of the system: a machined brass collar that recesses into the shelf-pin hole so the K-10 pin seats clean and tight instead of wallowing in bare wood. It's what turns an adjustable shelf from rattly to solid. Set these sleeves once ...Regular price From $53.76Regular priceUnit price per -
Circular Pulls
A solid-brass circular pull that mounts two ways: surface-mounted to sit proud as a deliberate detail, or flush-mounted to recess clean into the face. Either way the lines stay quiet — a machined ring with a matte finish that doesn't compete with ...Regular price From $44.86Regular priceUnit price per -
Back Mounted Stop Hinge
A stop hinge with the 95° stop built into the leaf — a hinge and a lid stay in one part. It sets into a shallow mortise and screws down flush, so the lid opens to 95° and holds there. No separate lid support to mount, align, or replace. This is th...Regular price $76.00Regular priceUnit price per -
HD-702 Box Feet
Add a touch of timeless elegance and sturdy support to your handcrafted boxes and cases with the Brusso HD-702 brass decorative box feet. The HD-702 features a sophisticated design, comprising a square base with a subtly radiused inner corner and ...Regular price $34.05Regular priceUnit price per -
MC-437 Knob
The MC-437 brass hook, with a flattened dome face ringed by a band-shaped edge, is pressure-fit and glued into place. It measures 3/8" [10 mm] in diameter and projects 15/16" [24 mm]. The mounting dowel is 3/16" [5 mm] in diameter.Regular price $17.00Regular priceUnit price per
Reviews / 4.9 average / 726 ratings
Worth every penny - their words, not ours
★★★★★
Exceptional quality and finish
Quality and finish were exceptional, 100% recommend. I've used Brusso hardware for high end projects for years.
★★★★★
Well made and beautiful
Love love love your products. Well made accurate and beautiful.
★★★★★
High quality and precise
They're perfect. Thanks Brusso for making such high quality and precise hardware!
Solid-brass box and cabinet hardware machined in the USA - feet, hooks, knobs, lid stays, and catches - made to match Brusso hinges. Browse by type, all solid brass.
FAQ
Common questions
Does this match Brusso hinges?
Yes. The hardware is machined from the same solid brass and finished to match, so feet, catches, knobs, and pulls sit consistently with the hinges on a piece.
Is it solid brass?
Yes - turned or machined from solid brass bar stock, not plated pot metal.
