Collection: Products

A stop hinge with the 95° stop built into the leaf — a hinge and a lid stay in one part. It sets into a shallow mortise and screws down flush, so the lid opens to 95° and holds there. No separate lid support to mount, align, or replace. This is th...

A full-mortise butt hinge milled from solid brass bar stock — not stamped or rolled. The knuckle is true, the leaves are flat and thick, and the pin runs straight, so the door swings without play and the gap stays even top to bottom. The differenc...

A solid-brass box hinge with a built-in stop. The lid opens to 95° and holds there — no separate lid stay, no chain, no sag. The stop is machined into the knuckle, so one pair does the work of a hinge and a lid support, with nothing extra to mount...

Our Limited Edition, American-Made Brusso Brushed Cotton Cap is crafted with soft brushed cotton, offering that broken-in feel right from the start. This five panel hat is the ideal way to show your appreciation for American-made excellence withou...

A center pivot hinge that mortises into the top and bottom of the door — only the pivot shows. The door swings free of the frame on a single axis, so you can run a door with no visible barrel and no side clearance to the case. Same idea as the off...

A solid-brass circular pull that mounts two ways: surface-mounted to sit proud as a deliberate detail, or flush-mounted to recess clean into the face. Either way the lines stay quiet — a machined ring with a matte finish that doesn't compete with ...

Add a touch of timeless elegance and sturdy support to your handcrafted boxes and cases with the Brusso HD-702 brass decorative box feet. The HD-702 features a sophisticated design, comprising a square base with a subtly radiused inner corner and ...

The JB-426S stainless-steel decorative box foot, comprised of a compressed sphere and spacing collar with turned profile, is pressure-fit and glued into place. Stainless steel gives the foot a modern look and does not tarnish, making it suitable f...

Everything the hardware side of a jewelry box needs, in one kit — so you can build the box instead of chasing hardware. Inside: Brusso Stop Hinges - JB-102 (one pair): the lid opens to 95° and holds there — no separate lid stay, no flop. One par...

A lid stay that mortises into the side of the box and anchors into the lid — it catches the lid at the open position and holds it, so the lid doesn't fall back or strain the hinges. The flanged anchor is precision machined and glued into the lid f...

Solid-brass lift-off hinge: the two leaves separate, so the door lifts straight off its pins without unscrewing anything. Hang it, level it once, and from then on the door comes off and goes back on in seconds — for finishing, for fitting, for mov...

The Brusso LI Intermediate Knife Hinge is engineered to provide essential additional strength and support for larger doors, perfectly filling a critical gap in our knife hinge line. Proudly made in the USA, this hinge embodies Brusso's commitment ...

The MC-437 brass hook, with a flattened dome face ringed by a band-shaped edge, is pressure-fit and glued into place. It measures 3/8" [10 mm] in diameter and projects 15/16" [24 mm]. The mounting dowel is 3/16" [5 mm] in diameter.

The MC-444S stainless steel decorative box foot, comprised of a leg with cove profile, straight collar, and pad foot, is pressure-fit and glued into place. Stainless steel gives the foot a modern look and does not tarnish, making it suitable for k...

At Brusso Hardware, we understand that true precision in woodworking begins long before the first piece of hardware is installed. It starts with the accurate layout of your project. That's why we're proud to offer the NAREX Marking Knife with Fing...

The NAREX Wheel Marking Gauge is an essential tool for the discerning woodworker, designed to deliver the precise, repeatable layout lines that are foundational to superior craftsmanship. Scribe Disc: At the heart of this gauge is a hardened too...

A knife hinge that carries the door on a single pivot pin — top and bottom — so the only thing visible from the front is a thin brass line at the edge. No barrel, no leaves stamped across the face. The door appears to swing on nothing. This is the...

A spring-loaded brass ball catch that holds a door shut and lets it go with a press. That click when it seats, and a clean release when you pull. A steel ball rides in a machined brass cylinder against a matching keeper, so the catch is positive e...

A solid-brass push-button latch that sits flush and hides inside the box. Press the button, the spring-loaded bar releases, the lid opens. Close it and it catches with a click you can feel. This is the closure for the maker who wants the box to lo...

A quadrant hinge machined to the tolerance the install actually demands. The curved quadrant arm sweeps through a mortise in the box wall, so the lid opens, stops, and stays — the look of a high-end humidor or presentation box, with no visible lid...

Invest in a tool that stands the test of time. The Richter Bevel Edge Chisel is an investment in your craft, ensuring every cut contributes to a legacy of exceptional work. Superior Materials: The blade is forged from high-quality forged chrome ...

A small solid-brass box foot — a turned sphere tapering to a disk — that lifts a box off the surface and finishes the bottom edge. Pressure-fit and glued on a 5/16"" dowel, so it sits flush and shows nothing but brass. Feet are the detail most mak...

A wood screw lubricant that lets a screw drive with far less torque, so it goes in clean instead of snapping off in your hardwood or stripping the head. Rub the threads through the wax, drive the screw, done. One of the few items we don't make our...

The full adjustable-shelf system in one kit: twelve K-2 sleeves and four K-10 pins. The sleeves recess into your holes, the pins seat tight, and the shelf sits level and adjusts for the life of the piece — no rattle, no wallowed-out wood. Pick you...

A shelf support pin with a milled brass head and a clean barrel peg — the part of an adjustable shelf that actually shows. It drops into the K-2 sleeve for a fit with no rattle and no slop, so the shelf sits dead level and stays there. Most shelf ...

The sleeve half of the system: a machined brass collar that recesses into the shelf-pin hole so the K-10 pin seats clean and tight instead of wallowing in bare wood. It's what turns an adjustable shelf from rattly to solid. Set these sleeves once ...

A full-mortise side rail hinge with a built-in 95° stop, milled from thick solid brass. The lid swings up, catches at 95°, and holds — no separate lid stay, no chain. The stop is built into the hinge, so the inside of the box stays clean. Where a ...

A small solid-brass knob for boxes, small drawers, and lids — a flattened dome face ringed by a turned band, pressure-fit and glued so nothing shows but the brass. No screw head, no backplate, just a clean point to grip. On a small box, the knob i...